Rainbow-electronics MAX1139 Bedienungsanleitung

General DescriptionThe MAX1136–MAX1139 low-power, 10-bit, multichan-nel analog-to-digital converters (ADCs) feature internaltrack/hold (T/H), voltage

MAX1136–MAX1139signal. At the end of the acquisition interval, the T/Hswitches move to the hold position retaining the chargeon CT/Has a stable sample

swing from (GND - 0.3V) to (VDD+ 0.3V) without caus-ing damage to the device. For accurate conversionsthe inputs must not go more than 50mV below GND

MAX1136–MAX1139Slave Address A bus master initiates communication with a slave deviceby issuing a START condition followed by a slaveaddress. When idl

Configuration/Setup Bytes (Write Cycle)A write cycle begins with the bus master issuing aSTART condition followed by seven address bits (Figure7) and

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs14 __________________________________________________

Data Byte (Read Cycle)A read cycle must be initiated to obtain conversionresults. Read cycles begin with the bus master issuinga START condition follo

MAX1136–MAX1139The device memory contains all of the conversionresults when the MAX1136–MAX1139 release SCL. Theconverted results are read back in a f

External ClockWhen configured for external clock mode (CLK = 1),the MAX1136–MAX1139 use the SCL as the conversionclock. In external clock mode, the MA

MAX1136–MAX113910ms prior to conversion or powered continuously.Wake-up is invisible when using an external reference orVDDas the reference.Automatic

ground’s power supply is low impedance and as shortas possible. Route digital signals far away from sensi-tive analog and reference inputs.High-freque

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs2 ___________________________________________________

Effective Number of Bits Effective number of bits (ENOB) indicates the globalaccuracy of an ADC at a specific input frequency andsampling rate. An ide

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs_____________________________________________________

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCsMaxim cannot assume responsibility for use of any cir

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs_____________________________________________________

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs4 ___________________________________________________

Note 1: For DC accuracy, the MAX1136/MAX1138 are tested at VDD= 5V and the MAX1137/MAX1139 are tested at VDD= 3V. All devices are configured for unipo

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs6 ___________________________________________________

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs_____________________________________________________

MAX1136–MAX11392.7V to 3.6V and 4.5V to 5.5V, Low-Power, 4-/12-Channel, 2-Wire Serial 10-Bit ADCs8 ___________________________________________________

Detailed DescriptionThe MAX1136–MAX1139 analog-to-digital converters(ADCs) use successive-approximation conversion tech-niques and fully differential