MAX6629–MAX6632
12-Bit + Sign Digital Temperature Sensors
with Serial Interface
2 _______________________________________________________________________________________
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
All Voltages Referenced to GND
V
CC
...........................................................................-0.3V, +6.0V
SO, SCK, CS ....................................................-0.3V, V
CC
+ 0.3V
SO .......................................................................-1mA to +50mA
Current into Any Pin ............................................................10mA
Continuous Power Dissipation (T
A
= +70°C)
6-Pin SOT23 (derate 9.10mW/°C above +70°C)..........727mW
Junction Temperature......................................................+150°C
Operating Temperature Range (Note 1) ...........-55°C to +150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature .............................................................Note 2
ELECTRICAL CHARACTERISTICS
(V
CC
= +3.0V to +5.5V, T
A
= -55°C to +125°C, unless otherwise noted. Typical values are at V
CC
= +3.3V and T
A
= +25°C.) (Notes 3
and 4)
PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS
TEMPERATURE
T
A
= room temp, V
CC
= +3.3V -0.8 ±0.2 +0.8
0°C ≤ T
A
≤ +70°C, V
CC
= +3.3V -1.0 ±0.2 +1.0
-20°C ≤ T
A
≤ +85°C, V
CC
= +3.3V -1.6 +0.3 +1.6
-20°C ≤ T
A
≤ +100°C, V
CC
= +3.3V -2.3 +0.5 +2.3 °C
-40°C ≤ T
A
≤ +125°C, V
CC
= +3.3V -3.2 +0.8 +3.2
T
A
≥ -55°C, V
CC
= +3.3V -1.0 +1.5 +3.5
Accuracy
T
A
= +150°C, V
CC
= +3.3V -5.0 +1.5 +6.5
Power-Supply Sensitivity PSS 0.2 0.6 °C/V
Resolution 0.0625 °C
MAX6629, MAX6630, CS high 0.37 0.5 0.65
Ti me Betw een C onver sion S tar ts t
SAMPLE
MAX6631, MAX6632, CS high 5.9 8 10.5
s
Conversion Time t
CONV
180 250 320 ms
POWER SUPPLY
Supply Voltage Range V
CC
3.0 5.5 V
I
SD
Shutdown (Note 4), V
CC
= +0.8V 5
I
IDLE
ADC idle (Figure 2), CS = low 6 20Supply Current, SCK Idle
I
CONV
ADC converting (Figure 2) 360 650
µA
MAX6629, MAX6630 200 400
Average Operating Current I
CC
MAX6631, MAX6632 32 50
µA
Power-On Reset (POR)
Threshold
V
CC
falling 1.6 V
Note 1: It is not recommended to operate the device above +125°C for extended periods of time.
Note 2: This device is constructed using a unique set of packaging techniques that impose a limit on the thermal profile the device
can be exposed to during board-level solder attach and rework. This limit permits only the use of the solder profiles
recommended in the industry-standard specification, JEDEC 020A, paragraph 7.6, Table 3 for IR/VPR and Convection
Reflow. Preheating is required. Hand or wave soldering is not allowed.
(552 Seiten)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern