Rainbow-electronics MAX6871 Bedienungsanleitung PDF herunterladen (Seite 1)

General Description

The MAX6870/MAX6871 EEPROM-configurable, multi-

voltage supply sequencers/supervisors monitor several

voltage detector inputs, two auxiliary inputs, and four

general-purpose logic inputs. The MAX6870/MAX6871

feature programmable outputs for highly configurable

power-supply sequencing applications. The MAX6870

features six voltage detector inputs and eight program-

mable outputs, while the MAX6871 features four voltage

detector inputs and five programmable outputs. Manual

reset and margin disable inputs offer additional flexibility.

All voltage detectors offer two configurable thresholds

for undervoltage/overvoltage or dual undervoltage

detection. One high voltage input (IN1) provides detec-

tor threshold voltages from +2.5V to +13.2V in 50mV

increments, or from +1.25V to +7.625V in 25mV incre-

ments. A bipolar input (IN2) provides detector threshold

voltages from ±2.5V to ±15.25V in 50mV increments, or

from ±1.25V to ±7.625V in 25mV increments. Positive

inputs (IN3–IN6) provide detector threshold voltages

from +1V to +5.5V in 20mV increments, or from +0.5V

to +3.05V in 10mV increments.

Programmable output stages control power-supply

sequencing or system resets/interrupts. Programmable

output options include: active-high, active-low, open-

drain, weak pullup, push-pull, and charge pump.

Programmable timing delay blocks configure each output

to wait between 25µs and 1600ms before deasserting. A

fault register logs the condition that caused each output

to assert (undervoltage, overvoltage, manual reset, etc.).

An internal 10-bit ADC monitors the voltage detector

inputs, and two auxiliary inputs through a multiplexer

that automatically sequences through all inputs every

200ms. A SMBus

-/I

-compatible, serial data inter-

face programs and communicates with the configuration

EEPROM, the configuration registers, the internal 4kb

user EEPROM, the ADC registers, and the fault registers

of the MAX6870/MAX6871.

The MAX6870/MAX6871 are available in a 7mm x 7mm

x 0.8mm 32-pin thin QFN package and operate over

the extended -40°C to +85°C temperature range.

Applications

Telecommunications/Central Office Systems

Networking Systems

Servers/Workstations

Basestations

Storage Equipment

Multimicroprocessor/Voltage Systems

Features

♦ Six (MAX6870) or Four (MAX6871) Configurable

Input Voltage Detectors

One High Voltage Input (+1.25V to +7.625V or

+2.5V to +13.2V Thresholds)

One Bipolar Voltage Input (±1.25V to ±7.625V

or ±2.5V to ±15.25V Thresholds)

Four (MAX6870) or Two (MAX6871) Positive

Voltage Inputs (+0.5V to +3.05V or +1V to

+5.5V Thresholds)

♦ Four General-Purpose Logic Inputs

♦ Two Configurable Watchdog Timers

♦ Eight (MAX6870) or Five (MAX6871)

Programmable Outputs

Active-High, Active-Low, Open-Drain, Weak

Pullup, Push-Pull, Charge-Pump

Timing Delays from 25µs to 1600ms

♦ 10-Bit Internal ADC Monitors the Input Voltage

Detectors and Two Auxiliary Inputs

♦ Margining Disable and Manual Reset Controls

♦ Internal 1.25V Reference or External Reference

Input

♦ 4kb Internal User EEPROM

Endurance: 100,000 Erase/Write Cycles

Data Retention: 10 Years

♦ I

C/SMBus-Compatible Serial

Configuration/Communication Interface

♦ ±1% Threshold Accuracy

MAX6870/MAX6871

EEPROM-Programmable Hex/Quad

Power-Supply Sequencers/Supervisors with ADC

________________________________________________________________ Maxim Integrated Products 1

Ordering Information

19-3384; Rev 1; 9/04

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

EVALUATION KIT

AVAILABLE

Pin Configurations, Typical Operating Circuit, and Selector

Guide appear at end of data sheet.

PART

TEMP RANGE

PIN-

PACKAGE

PKG

CODE

MAX6870ETJ

-40°C to +85°C 32 Thin QFN

T3277-2

MAX6871ETJ

-40°C to +85°C 32 Thin QFN

T3277-2

SMBus is a trademark of Intel Corp.

C is a trademark of Philips Corp.

Purchase of I

C components from Maxim Integrated Products,

Inc., or one of its sublicensed Associated Companies, conveys

a license under the Philips I

C Patent Rights to use these com-

ponents in an I

C system, provided that the system conforms

to the I

C Standard Specification as defined by Philips.

1 2 3 4 5 6 ... 50 51

Inhaltsverzeichnis

Seite 1 - EEPROM-Programmable Hex/Quad

General DescriptionThe MAX6870/MAX6871 EEPROM-configurable, multi-voltage supply sequencers/supervisors monitor severalvoltage detector inputs, two au

Seite 2

MAX6870/MAX6871Detailed DescriptionThe MAX6870/MAX6871 EEPROM-configurable, multi-voltage supply sequencers/supervisors monitor severalvoltage-detecto

Seite 3

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 4

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC12 ____________________________________________________________

Seite 5

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 6

Set the primary and secondary threshold voltages foreach voltage-detector input with registers 00h–0Bh.Each primary threshold voltage must be an under

Seite 7

where VTHis the desired threshold voltage and x is thedecimal code for the desired threshold (Table 3).IN3–IN6IN3–IN6 offer positive voltage detectors

Seite 8

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC16 ____________________________________________________________

Seite 9

AUXIN1 and AUXIN2The AUXIN1 and AUXIN2 high-impedance analog inputsare intended to monitor two additional system voltagesnot required for power-supply

Seite 10

MAX6870/MAX6871MARGINMARGIN allows system-level testing while power sup-plies exceed the normal ranges. Registers 41h and 42hdetermine whether the pro

Seite 11

REFINThe MAX6870/MAX6871 feature an internal +1.25V volt-age reference. The voltage reference sets the thresholdof the voltage detectors and provides

Seite 12

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC2 _____________________________________________________________

Seite 13

MAX6870/MAX6871Table 10 only applies to PO1 of the MAX6870. Write a 0to a bit to make the PO1 output independent of therespective signal (IN1–IN6 prim

Seite 14

Table 11 only applies to PO2 of the MAX6870. Write a 0to a bit to make the PO2 output independent of therespective signal (IN1–IN6 primary or secondar

Seite 15

MAX6870/MAX6871Table 12 only applies to PO3 of the MAX6870 and PO1of the MAX6871. Write a 0 to a bit to make the PO3/PO1output independent of the resp

Seite 16

Table 13 only applies to PO3 of the MAX6870 and PO1of the MAX6871. Write a 0 to a bit to make the PO3/PO1output independent of the respective signal (

Seite 17

MAX6870/MAX6871Table 14 only applies to PO4 of the MAX6870 and PO2of the MAX6871. Write a 0 to a bit to make the PO4/PO2output independent of the resp

Seite 18

Table 15 only applies to PO4 of the MAX6870 and PO2of the MAX6871. Write a 0 to a bit to make the PO4/PO2output independent of the respective signal (

Seite 19

MAX6870/MAX6871Table 16 only applies to PO5 of the MAX6870 and PO3of the MAX6871. Write a 0 to a bit to make the PO5/PO3output independent of the resp

Seite 20

Table 17 only applies to PO5 of the MAX6870 and PO3of the MAX6871. Write a 0 to a bit to make the PO5/PO3output independent of the respective signal (

Seite 21

MAX6870/MAX6871Table 18 only applies to PO6 of the MAX6870 and PO4of the MAX6871. Write a 0 to a bit to make the PO6/PO4output independent of the resp

Seite 22

Table 19 only applies to PO6 of the MAX6870 and PO4of the MAX6871. Write a 0 to a bit to make the PO6/PO4output independent of the respective signal (

Seite 23

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 24

MAX6870/MAX6871Table 20 only applies to PO7 of the MAX6870 and PO5of the MAX6871. Write a 0 to a bit to make the PO7/PO5output independent of the resp

Seite 25

Table 21 only applies to PO8 of the MAX6870. Write a 0to a bit to make the PO8 output independent of therespective signal (IN1–IN6 primary or secondar

Seite 26

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC32 ____________________________________________________________

Seite 27

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 28

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC34 ____________________________________________________________

Seite 29

condition frees the bus for another transmission. The busremains active if a REPEATED START condition is gener-ated, such as in the block read protoco

Seite 30

MAX6870/MAX6871SA7 through SA4 represent the standard interfaceaddress (1010) for devices with EEPROM. SA3 and SA2correspond to the A1 and A0 address

Seite 31

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 32

MAX6870/MAX6871directed into the user EEPROM. If the command code is80h, the data byte must be in the range of 00h to 45h. Ifthe command code is 81h o

Seite 33

address pointer automatically increments after eachdata byte, except when the address pointer is alreadyat 45h. If the address pointer is already 45h,

Seite 34

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC4 _____________________________________________________________

Seite 35

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC40 ____________________________________________________________

Seite 36

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 37

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC42 ____________________________________________________________

Seite 38

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 39

MAX6870/MAX6871and WDI_ bits assert if any of the GPI_ inputs are config-ured as watchdog inputs (WDI_) and a watchdog faultoccurs. Configuration Lock

Seite 40

Applications InformationConfiguration Download at Power-upThe configuration of the MAX6870/MAX6871 (undervolt-age/overvoltage thresholds, PO_ timeout

Seite 41

MAX6870/MAX6871Forcing ProgrammableOutputs High During Power-UpA weak 10µA pulldown holds all programmable outputslow during power-up until ABP exceed

Seite 42

Temperature Sensor OutputsFigure 11 shows the MAX6870/MAX6871 in a tempera-ture-sensing application with the DS600. The DS600generates an analog outpu

Seite 43

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC48 ____________________________________________________________

Seite 44

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 45

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 46

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC50 ____________________________________________________________

Seite 47

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADCMaxim cannot assume responsibility for use of any circuitry oth

Seite 48

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC6 _____________________________________________________________

Seite 49

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Seite 50

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC8 _____________________________________________________________

Seite 51

MAX6870/MAX6871EEPROM-Programmable Hex/QuadPower-Supply Sequencers/Supervisors with ADC_______________________________________________________________

Kommentare zu diesen Handbüchern

Keine Kommentare

Rainbow-electronics MAX6871 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Rainbow-electronics MAX6871 herunter. Rainbow Electronics MAX6871 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Rainbow-electronics MAX6871 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Sensoren Rainbow-electronics MAX6871 herunter. Rainbow Electronics MAX6871 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sensoren Rainbow-electronics MAX6871