Rainbow-electronics GM862-QUAD-PY Bedienungsanleitung Seite 132
- Seite / 434
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
AT Commands Reference Guide
80000ST10025a Rev. 5 - 09/07/08
Reproduction forbidden without Telit Communications S.p.A. written authorization - All Rights Reserved page 132 of 434
+CCLK - Clock Management SELINT 0 / 1
yy - year (two last digits are mandatory), range is 00..99
MM - month (two last digits are mandatory), range is 01..12
dd - day (two last digits are mandatory), range is 01..31 (if the month MM
has less than 31 days, the clock will be set for the next month)
hh - hour (two last digits are mandatory), range is 00..23
mm - minute (two last digits are mandatory), range is 00..59
ss - seconds (two last digits are mandatory), range is 00..59
±zz - time zone (indicates the difference, expressed in quarter of an hour,
between the local time and GMT; two last digits are mandatory),
range is -47..+48
Note: If the parameter is omitted the behavior of Set command is the same
as Read command.
AT+CCLK?
Read command returns the current setting of the real-time clock, in the
format <time>.
Note: the three last characters of <time> are not returned by +CCLK?
because the ME doesn’t support time zone information.
AT+CCLK=?
Test command returns the OK result code.
Example
AT+CCLK="02/09/07,22:30:00+00"
OK
AT+CCLK?
+CCLK: 02/09/07,22:30:25
OK
Reference GSM 07.07
+CCLK - Clock Management SELINT 2
AT+CCLK=<time>
Set command sets the real-time clock of the ME.
Parameter:
<time> - current time as quoted string in the format:
"yy/MM/dd,hh:mm:ss±zz"
yy - year (two last digits are mandatory), range is 00..99
MM - month (two last digits are mandatory), range is 01..12
dd - day (two last digits are mandatory), range is 01..31 (if the month MM
has less than 31 days, the clock will be set for the next month)
hh - hour (two last digits are mandatory), range is 00..23
mm - minute (two last digits are mandatory), range is 00..59
ss - seconds (two last digits are mandatory), range is 00..59
±zz - time zone (indicates the difference, expressed in quarter of an hour,
between the local time and GMT; two last digits are mandatory),
range is -47..+48
AT+CCLK?
Read command returns the current setting of the real-time clock, in the
format <time>.
Note: the three last characters of <time>, i.e. the time zone information, are
- AT Commands Reference Guide 1
- SW Version 2
- 7.03.00 / 7.02.05 2
- Contents 3
- DISCLAIMER 5
- 1 INTRODUCTION 6
- 2 APPLICABLE DOCUMENTS 7
- 3 AT COMMANDS 8
- 3.2 AT Command Syntax 9
- 3.2.1 String Type Parameters 10
- 3.2.2 Command Lines 10
- Valid for SELINT 0,1 only 15
- (context activation + DNS 17
- 3.2.5 Command Issuing Timing 19
- 3.3 Storage 20
- Valid for #SELINT=2 only 22
- 3.5 AT Commands References 31
- 3.5.3.1.2 Soft Reset - Z 34
- 3.5.3.1.24 Speaker Mode - M 40
- 3.5.3.2.1 Command Echo - E 40
- 3.5.3.3 Call Control 50
- 3.5.3.3.2 Tone Dial - T 54
- 3.5.3.3.3 Pulse Dial - P 55
- 3.5.3.3.4 Answer - A 55
- 3.5.3.3.5 Disconnect - H 55
- 3.5.3.4 Modulation Control 56
- 3.5.3.5 Compression Control 57
- 3.5.3.6 Break Control 58
- 3.5.3.7 S Parameters 59
- 3.5.3.7.2 Ring Counter - S1 60
- 3.5.4.1 General 68
- 3.5.4.2 Call Control 71
- ATD03282131321; 112
- 3.5.4.4.3 Enter PIN - +CPIN 114
- #SHDN #CSURVUC +CREG $GPSWK 120
- #WAKE #CSURVB +COPS $GPSSAV 120
- #GPIO #CSURVF +CPAS $GPSCON 120
- #ADC +CFUN $GPSPRG 120
- 3.5.4.6 Voice Control 148
- 3.5.4.7 Commands For GPRS 150
- Scheme 178
- 3.5.6.1.2 Model ID - +FMM 233
- 3.5.6.3 Serial Port Control 236
- 3.5.7 Custom AT Commands 238
- - (G-L): User Defined Tones 247
- AT#PSAV 296
- 3.5.7.3.2 Socket Info - #SI 316
- 3.5.7.3.7 Socket Dial - #SD 321
- 3.5.7.4 FTP AT Commands 326
- 3.5.7.4.4 FTP Put - #FTPPUT 327
- 3.5.7.4.5 FTP Get - #FTPGET 328
- 3.5.7.5.8 Query DNS - #QDNS 341
- #CSURVUC 388
- #CSURVNLF 392
- Interpreter, AT Commands 409
- 3.5.7.10.8 Reboot - #REBOOT 417
- 4 List of acronyms 431
- 5 Document Change Log 433
Verwandte Produkte und Handbücher für GPS-Empfänger Rainbow-electronics GM862-QUAD-PY
(2 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern